Care and transport

How to Lock a Kayak on Your Car

Driving tie-downs are the straps or ties that hold the boat on the rack while driving. A crossbar is the horizontal rack bar; a carrier supports the boat on it, and towers attach the rack to the vehicle. Each lock secures a different connection.

Choose a lock

  • If convenience at a short stop matters, consider locking straps such as Yakima RipCord. Their buckle locks and steel cable connect the boat to the crossbars; keep the driving tie-downs in place and follow the carrier instructions. Yakima’s manual limits the combined weight of the base system (the rack supporting the carrier), RipCord and load to 165 lb (75 kg) or the vehicle manufacturer’s lower rating.2,4
  • If your boat has no suitable fixed opening, consider Malone Lariat’s paired end loops. If a loop could slip off or go around only a removable accessory, change the route or product before leaving the boat. Malone requires bow and stern safety tie-downs—the driving restraints at the boat’s front and rear—for all rooftop transport; keep them in place in addition to the Lariat lock cables.5,1,6 Yakima warns that inadequately secured loads and incorrectly mounted roof racks and accessory racks can come loose during travel and cause serious accidents.7
  • If your carrier or rack towers already lock, add a separate boat lock. Thule’s Hull-a-Port XTR locks to the crossbars with Thule One-Key System lock cylinders (sold separately); Malone says its SteelTop and AirFlow racks are supplied with tower locking systems.8,6 The XTR supports one boat up to 75 lb or two boats with a combined weight of 130 lb or less. The lower of the assembly instructions’ maximum load and the vehicle manufacturer’s recommended maximum load applies. Count the load carrier, any fitted carrier accessories and the load itself toward the vehicle’s maximum roof load. Do not use it off-road or install it on a trailer; remove the keys and keep them inside the vehicle during transport.8
  • If you already have lockable Thule or Yakima equipment, choose compatible lock cylinders in that maker’s system so the equipment can share a key. Yakima’s packaged cores cannot be ordered by a chosen number.9,10
  • If the trip is over, unload the boat and rack rather than using the roof as storage. NRS warns that storing a plastic kayak bottom-down on sawhorses or a garage floor can dent its hull, the boat’s bottom.11 Suspenz recommends storing your kayak on its side to avoid hull damage, calling the side the boat’s strongest part.12 For security at home, see how to store a kayak.

Key Takeaways

  • Match the lock to the connection you want to secure: boat to bar, carrier to bar, or rack to vehicle.
  • Keep the boat’s required driving tie-downs in place; a lock is not a substitute for them.
  • Measure the route on your own boat and rack, then check that the closed loop cannot slip off.
  • Treat locks as deterrents, not guarantees against theft.1,5,3

Choose the connection to lock

A cable through the boat and around a crossbar directly connects the boat to the rack. A locking strap combines a strap and lock for a similar boat-to-bar connection.

A locking carrier secures the carrier to the bars. Thule’s lock holds the carrier to the crossbars.8 DocksLocks says cam straps and tie-downs pop open by hand in moments and offer zero theft protection.1,4

OptionChoose whenConnection securedConnection still to addressSource
Steel cableYou can route it through a fixed boat point and around a barBoat to crossbarKeep driving tie-downs in place; check that the loop cannot slip offDocksLocks1
Locking strapYou want a strap with a locking buckle for a brief stopBoat to crossbarFollow carrier instructions for driving tie-downsREI; Yakima RipCord2,4
Locking carrierYou have a compatible carrier that locks to the barsCarrier to crossbarLock the boat separatelyThule Hull-a-Port XTR8
Tower lockYou want to secure rack hardware to the vehicleRack towers to the vehicleLock the boat and carrier connections separatelyMalone6

These products are sold as deterrents. DocksLocks, Malone and Thule each caution that their locks are not guarantees against theft or theft-proof.1,5,3

In its comparison, DocksLocks says thin cables can be cut with small cutters, thick braided steel cables resist hand tools, and hardened chains offer its highest resistance but are heavier and less flexible. These are the maker’s qualitative comparisons, not security ratings; it says locks can be defeated with enough tools and time.13

Route a cable through the boat and rack

Before locking, choose a fixed point on the boat, such as a molded carry handle, security bar or scupper hole. A scupper is a drainage hole in a sit-on-top kayak.

Check that the cable reaches around the boat and crossbar, goes around the bar itself rather than a removable accessory, and forms a closed loop that cannot easily slide off. Cable reach depends on your planned route, so check it on your setup.1

With the kayak secured for travel:

  1. Route the cable through the fixed boat point you selected.
  2. Loop it around the crossbar so the bar itself is enclosed.
  3. Close the lock and spin the combination dials to random digits, if it has them.
  4. Check that the loop cannot slip off and that the cable does not interfere with the required driving tie-downs.1

For an alternative route, Malone’s Lariat has two cables: place one loop around the bow and slide it toward the center, then do the same at the stern.

Malone’s Lariat

Wrap the cables around the crossbars to remove slack and lock them with the key.

Malone lists the cable as 70 inches long and ⅜ inch in diameter; check your boat’s shape and rack rather than treating those dimensions as a boat-length limit.5

Locking straps, carriers and shared keys

Yakima RipCord is a set of two nylon-coated steel-cable straps with rubber-coated buckles and included SKS lock cores, which are replaceable lock cylinders in Yakima’s same-key system.

For its routing, loop a strap under the far side of the crossbar, over the load and under the near side. Hold the red button, feed the strap through the lock, tighten it, secure the extra strap and lock both RipCords. Keep the kayak’s driving tie-downs in place and follow the carrier instructions.4

RipCord instructions

If you do not understand the RipCord instructions or lack installation experience, Yakima says to have a professional installer fit the product. Its instructions also say to check before each use and tighten if needed, tie down both ends of long loads, and use caution when opening the hatch or sunroof.

Do not throw a strap or buckle around the vehicle where it could strike glass or dent the vehicle.4,14 For a vehicle with a sunroof or panoramic glass roof, Yakima’s SightClip instructions say to ensure adequate clearance with the roof rack and/or accessories installed before operation.15

Owner reviews of kayak locks

31 of 511 owner reviews of kayak locks mention problems with construction or finish; adjusted for the extra one- and two-star reviews in our collection, about 3 in 100, so check a locking strap before each use and tighten it if needed, as Yakima directs for its RipCord (owner reviews, not a rate for all buyers).16 Based on published customer reviews, which we do not independently verify for authenticity.

A shared-key setup

A shared-key setup can reduce the number of keys you carry, but the cylinders must be compatible with your equipment. Thule’s One-Key System two-pack has two locks that you operate separately with the same key.

For Yakima SKS cores, use the matching-core link on Yakima’s product page to order individual cores: select the code matching your existing key and the quantity you need. You cannot choose the core number in a prepackaged set.

Use the flat-edged control key to install a core. To remove one, first put the lock in the unlocked position, then insert the control key completely and pull the core out. The control key does not operate the lock. Remove the control key, then use the matching locking key to lock or unlock the accessory.9,10

Carrier and rack fit

Thule’s Hull-a-Port XTR is an example of a carrier that locks to crossbars with separately sold One-Key cylinders. Thule says its Hull-a-Port Aero carrier locks to the load bars with included locks and has a 75-pound (34-kilogram) load capacity.17

Malone says its SteelTop and AirFlow rack series include tower locking systems. Check the relevant maker’s fit guide for your vehicle and rack; Malone notes that some factory crossbars may need optional mounting bolts or may not be recommended.8,6

Yakima says its SUPDawg paddleboard carrier includes SKS locks for the rack and the board.18

Crossbar mounting

  • Yakima’s BigStack instructions show a mounting clamp that wraps around a round crossbar and snaps onto the carrier base.19
  • Thule lists the Hull-a-Port XTR as fitting load bars up to 3⅛ inches (80.5 millimeters) wide; check your bar width against that specification.8
  • INNO says its surf, SUP, kayak and canoe locker has a universal mounting system fitting aero, square, round and most factory crossbars.20
  • EXR says the square-crossbar variant of its U-bolt mounting kit is sized for traditional square aluminum or steel crossbars.21
  • EXR describes the aerodynamic version of its EXR2641 U-bolt mounting kit as contoured for wing-style and teardrop aluminum crossbars.21
  • Rhino-Rack says its Nautic Stack kit includes a universal clamp fixing style and a C-channel nut-and-bolt fixing style.22

Before leaving the car

For an overnight stop or extended absence, remove valuable gear if practical. If the boat must remain on the car, use a cable route that captures a fixed point on the boat and the crossbar, check for a loop that could slip off, and park in a lit area.

A hardened chain is another option if you accept the added weight and reduced flexibility. These are deterrent measures, not a promise that the boat will remain untouched.3,1,13

Transport restraints

Keep the transport restraints in place and follow their instructions; REI cautions that overtight straps can deform plastic hulls or crack fiberglass. For its foam-block transport setups, Swift Canoe & Kayak says to shake your kayak before driving and check that it is held firmly with no movement.23

Never drive with a lock, knob or rack in an open or unlocked position. Check the load at stops during the trip. Tiegear says to check your load and roof-rack straps after the first 10 to 15 minutes of driving, then at every fuel stop.24

Keep locks operating smoothly

Move locks periodically to keep them operating smoothly; Thule recommends graphite or dry lubricant for this purpose. If a Malone rack shows excessive corrosion, deformity or a mechanical defect, stop using it.2,3,6,25

For more on the restraints that hold a kayak during travel, see how to tie down a kayak. To compare roof-rack styles, see kayak roof racks compared.

Unload and store the boat

Once home, unload and store the boat properly; see how to store a kayak.14 Ocean Kayak’s owner’s manual cautions that, when hanging a kayak for storage, using the scupper holes may cause distortion and hanging from the toggle handles may put undue strain on them.26

Malone says the powder coat over E-coating on its Atlas storage racks allows dockside or garage use.27

Footnotes

  1. https://www.dockslocks.com/blogs/education/how-to-lock-a-kayak-to-a-roof-rack ↩ ↩2 ↩3 ↩4 ↩5 ↩6 ↩7 ↩8 ↩9

  2. https://www.rei.com/learn/expert-advice/transporting-kayak-canoe.html ↩ ↩2 ↩3 ↩4

  3. https://www.thule.com/-/s/approved/std.lang.all/31/07/553107.pdf?rev=4.4 ↩ ↩2 ↩3 ↩4 ↩5

  4. https://yakima.com/products/ripcord ↩ ↩2 ↩3 ↩4 ↩5

  5. https://maloneautoracks.com/Lariat-Universa-Kayak-Canoe-Cable-Lock.html ↩ ↩2 ↩3 ↩4

  6. https://maloneautoracks.com/FAQ.html ↩ ↩2 ↩3 ↩4 ↩5

  7. https://assets.yakima.com/product/instructions/8004073/1 ↩

  8. https://www.thule.com/en-us/water-racks/kayak-and-canoe-racks/thule-hull-a-port-xtr-_-848004 ↩ ↩2 ↩3 ↩4 ↩5 ↩6

  9. https://www.thule.com/en-us/bike-rack/accessories/thule-one-key-system-2-pack-_-450200 ↩ ↩2

  10. https://yakima.com/products/sks-lock-cores ↩ ↩2

  11. https://www.nrs.com/learn/boating-gear-storage-ideas ↩

  12. https://suspenz.com/pages/storage-tips ↩

  13. https://www.dockslocks.com/blogs/education/can-cable-locks-be-cut-what-actually-stops-a-thief ↩ ↩2

  14. https://www.nrs.com/learn/how-to-strap-kayaks-to-car ↩ ↩2

  15. https://assets.yakima.com/product/instructions/8006451/1 ↩

  16. Well Paddled owner-review count, figure 7168 (October 2026 count). Method: https://wellpaddled.com/about/owner-review-counts/ ↩

  17. Wayback Machine copy captured September 3, 2026 of https://www.thule.com/en-us/water-racks/kayak-and-canoe-racks/thule-hull-a-port-aero-_-849000 ↩

  18. https://yakima.com/products/supdawg ↩

  19. https://assets.yakima.com/product/instructions/8004041/1 ↩

  20. https://usa.innoracks.com/product/ina446-ina445-xa445/ ↩

  21. https://exrroofracks.com/products/exr-bolt-on-u-brackets-attach-roof-accessories-to-various-xbars-styles-4pcs-exr2641 ↩ ↩2

  22. https://www.rhinorack.com/en-us/products/sport-awnings/water-sports/kayak-carriers/nautic-stack_s520 ↩

  23. https://swiftcanoe.com/wp-content/uploads/2019/09/tiedown-tips.pdf ↩

  24. https://tiegear.com/blogs/news/how-to-tie-down-roof-rack-load ↩

  25. https://maloneautoracks.com/dealerimages/pdf/MPG215_216_217.pdf ↩

  26. https://johnsonoutdoors.widen.net/content/oeh5a6qppj/pdf/ocean_kayak_owners_manual_web.pdf ↩

  27. https://dc-docs.dcatalog.com/Malone-Auto-Racks/Malone-Auto-Racks/e97e81ec-320c-4f69-8e39-cb458a340f34/2026-HR-Catalog.pdf ↩