Check your life jacket’s fabric, fastenings, fit and flotation. Keep it clean, fully dry and free from compression between trips. Discard a waterlogged, faded or damaged foam jacket. If you own an inflatable, follow its exact model’s servicing instructions.1,2
This page summarizes published safety guidance. It is not a substitute for instruction, and conditions on your water may differ. Check the current rules for the state and water you paddle.
Key Takeaways
- Test a foam jacket for wear and buoyancy at least annually.1
- Check straps, seams and fastenings often, including after possible damage.3,4
- Check fit and flotation in calm, protected water.2
- Air-dry thoroughly before storage; avoid compression and direct heat.2,3
- Inspect and service an inflatable according to its model’s manual.1
Inspect your foam jacket
A personal flotation device (PFD) is equipment that helps keep you afloat. The United States Coast Guard (USCG) says foam jackets should be tested for wear and buoyancy at least once a year. Astral recommends inspection at the beginning of each season; the NRS-hosted care leaflet also calls for frequent condition checks.1,2,3 The U.S. Coast Guard lists minimum adult buoyancy of 15.5 pounds (70 newtons) for Type III foam life jackets and 22.0 pounds (100 newtons) for Type III inflatables.5
Inspect the fabric for holes, tears and open seams. Check that zippers, buckles and webbing—the straps that secure the jacket—work properly. Give belts and ties a quick, hard pull to check their attachments. Look for waterlogging, mildew odor and shrinking buoyant material.2,3
For Mustang products, also check shoulder or sleeve areas for separation, seams for fraying, and fastenings for easy operation. Its inspection policy calls for examination annually and whenever safety is in doubt. Mold, mildew, compressed storage, nearby heat, weakened sun-bleached fabric, gasoline and prolonged oil contamination are concerns.4
The federal serviceability rule
Under 33 CFR 175.23:
“No PFD may exhibit deterioration that could diminish the performance of the PFD, including—”
Its buoyant-material clause includes:
“Buoyant material that has become hardened, non-resilient, permanently compressed, waterlogged, oil-soaked, or which shows evidence of fungus or mildew; or”6
The rule also excludes broken, deformed or corrosion-weakened hardware; torn or detached straps; and deteriorated structural parts that fail when tugged. Fabric openings must not allow buoyant material to escape. That material must remain present and securely positioned.6
Sections 175.15 and 175.21 require appropriate size and fit, a legible approval number, and compliance with the approval label. The National Safe Boating Council says to look inside the life jacket for its U.S. Coast Guard approval number, which appears on both old and new labels.7 The Minnesota Department of Natural Resources’ H₂O Toons guide advises checking for a “U.S. COAST GUARD APPROVED” label attached inside your life jacket.8 Use it as its owner’s manual requires if the label refers to one.9 The Coast Guard’s Lifejacket Approval Harmonization rule specifies the marking “USCG Approved” followed by the device’s unique approval number.10
Check fit and flotation in water
As one example, Mustang Survival’s MIT 70 manual says the device is designed for wearers over 16 years of age with a chest range of 30 to 52 inches (76 to 132 centimeters) who weigh over 90 pounds (41 kilograms); check the label’s wearer weight and chest size for your own jacket.11 A secure, comfortable fit should prevent the jacket from rising above your chin or ears. Try it in water to check that your airway stays clear.1
For an Astral jacket, loosen the adjustments, tighten the upper side straps followed by the lower ones, then adjust the shoulders.2 Fasten all straps, zippers and ties, and tuck away loose strap ends.3
Astral recommends a test swim in calm, protected water. Mustang specifies a controlled test with an observer. The NRS-hosted leaflet describes testing in shallow water: relax, tilt your head back, and check that your chin stays above water and breathing is easy. If your mouth is not well above water, replace the jacket or choose one with more buoyancy.2,4,3
Clothing and pocket contents can change performance. A calm-water check does not establish how the jacket will behave in swift or rough water.3 For a weighted buoyancy test, the Canadian Coast Guard’s SAR Seamanship Reference Manual says to use the support weight printed on the device’s label.12
Wash, dry and store it carefully
For Astral jackets, hand-wash with mild detergent and warm water after saltwater or especially dirty-water use, and before extended seasonal storage. Palm recommends rinsing its PFDs in clean, fresh water after each use.13 A nylon-bristle brush can help with stains. Avoid a top-loading washer with an agitator.2
Hang an Astral jacket out of direct sunlight and let it dry completely. Store it somewhere cool and dry without compression.2 The NRS-hosted leaflet also specifies thorough drip-drying, ventilation and avoiding radiators, heaters or other direct heat. Do not leave it aboard an unused boat for long periods.3
Avoid heavy objects on the jacket, and never use it as a kneeling pad or boat fender: crushing reduces buoyancy.3
While underway, wear your jacket. Wearable PFDs must be readily accessible; do not bury them beneath gear or stow them in plastic bags or locked or closed compartments. Do not attach your jacket to the boat.1,3
When to retire a foam jacket
USCG says to discard waterlogged, faded or otherwise damaged jackets.1 Marine Safety South Australia calls replacing life jackets every 10 years best practice.14 The Coast Guard publishes life-jacket safety notices on its Beacon Alerts page.15 Paddle UK reports that a recalled Patgear product, advertised as a life jacket but identified once purchased as a buoyancy aid, did not meet the minimum buoyancy requirement and that the recalled products lacked the required compliance documentation or markings.16 Astral advises considering replacement after damage or noticeably reduced flotation. Mustang explains that compressed foam can lose buoyancy; if you suspect significant loss, replace its garment or contact a Mustang dealer.2,4
Remove equipment that fails inspection from use. Mustang allows repair or replacement following evaluation; Astral advises against owner repairs or modifications because the jacket would no longer be approved by the USCG. Do not alter a poorly fitting jacket—get one that fits. The NRS-hosted leaflet says to cut up and discard unserviceable jackets.4,2,3 In April 2024, Paddle UK reported multiple recalls of buoyancy aids and life jackets sold through AliExpress, Fruugo and eBay that presented a serious risk of drowning.17 Paddle Northern Ireland reports three product recalls involving a life-jacket harness, buoyancy aids and life jackets described as “swim vests” sold online.18 The Royal Yachting Association reports an August 5, 2025 recall by the UK’s Office for Product Safety and Standards for specified Helly Hansen AS life jacket models.19
Service an inflatable by its exact model
An inflatable adds a bladder—the chamber that holds inflation air—and a mechanism that releases carbon dioxide (CO₂) from a cylinder. Oral inflation means filling it by mouth. Mustang Survival’s general inflatable-care guide recommends inflating by mouth until firm and leaving the jacket at a stable temperature for at least two hours, ideally overnight (16 hours); it also directs you to your model’s manual.20
USCG recommends maintenance according to the manufacturer’s instructions and requires a full cylinder and green inflator indicators showing that the mechanism is ready to inflate. It says inflatables are not appropriate for weak swimmers or non-swimmers.1,11
Federal serviceability requirements also cover air-holding chambers, clear and intact oral tubes, an accessible working manual pull cord or lever, and functioning indicators. The mechanism must be properly armed with a full cartridge. Bluestorm lists CO₂ cylinder weights of 24 grams for the Cirrus 26, 33 grams for the Stratus 35 and 38 grams for the Atmos 40.21 If the jacket is worn already inflated, the mechanism need not be armed, but all other condition requirements still apply.6
Mustang M.I.T. 70 MD4031 and MD4032
These instructions apply to MD4031 manual and MD4032 automatic, not MD4041 or other mechanisms. MD4031 requires pulling the tab; immersion will not activate it. MD4032 can inflate prematurely in heavy splashing, humidity, fog or rain. Premature inflation requires servicing before reuse and can damage a tightly stored jacket.11
The manual requires:
-
Before each wear: open both side closures; inspect for abrasion, tears, mildew, oil and foreign material. Check secure seams, sound straps and hardware, the mouth-inflation valve cap in its stowed position, an exposed pull tab and a green indicator. Red means fired or incorrectly fitted: rearm. For MD4032, also check the bobbin’s age using the purchase date of the device or bobbin; use the bobbin’s printed date if the purchase date is unknown. If that date is earlier than three years ago, rearm with a replacement bobbin.11
Rearming means discarding the used CO₂ cylinder assembly and fitting a new one from Mustang’s Re-Arm Kit MA4031 (on MD4032, also a new bobbin), then checking correct installation, a green indicator and a leak test as the manual directs.11
-
Every six months: thoroughly inspect and perform a leak test.11 Orally inflate until firm and leave for at least six hours.11 Loss of firmness means the device is leaking: Mustang says it should then be replaced, and that you contact Mustang Survival customer service if it leaks.11
-
After every inflation: rearm.11
-
Annually, preferably before the season: check components for dirt or corrosion; clean or replace as necessary. Inspect stitching, straps and hardware, leak-test, deflate, confirm green status, and record the date marked “annual” below the oral tube. Contact Mustang if uncertain. Test more often after potential damage or extreme use.11
MD4032 also needs its bobbin checked: this water-sensitive part sits inside the inflator’s threaded housing and triggers automatic inflation.
Check the bobbin’s age using the purchase date of the flotation device or bobbin; use the bobbin’s printed date if purchase timing is unknown. If that date is earlier than three years ago, Mustang’s manual says to rearm the device with a replacement bobbin.11 Replace used, activated or damaged bobbins and discard those exposed to gas, oil, water or high humidity. Test automatic operation at each season’s start.11
Rearming and testing precautions
Use the linked manual’s full rearming procedure and fold layout. Both models specify the MA4031 replacement rearming kit, containing a CO₂ cylinder with a 0.6-ounce (17-gram) charge and a bobbin; MD4031 does not use the bobbin. See Mustang’s model page for the maker’s linked manual.11
Discard the used cylinder assembly. Check that the replacement cylinder is unpierced. Its o-ring—the ring that seals the connection—and its sensor ring—the ring attached to the cylinder assembly—must both be present and undamaged. Turn its fitting clockwise one-eighth turn to the full stop: incomplete installation prevents inflation. Verify installation with a leak test.11
For MD4032, remove every fragment of the old bobbin. Keep its housing clear and dry; rinse away dirt and salt with fresh water, then dry. Install the bobbin white side up with slots aligned, and screw the cap to the housing shoulder before installing the cylinder, or the sensor ring can be damaged.11
For the manual-mechanism check, first remove the cylinder. Move the pull-tab lever down and up several times; the lever and the pin that punctures the CO₂ cylinder must move freely without binding.11
Deflate by reversing the mouth-inflation valve cap into the valve and gently squeezing; then restore the cap. Repack only after deflation and rearming, folding the sides outward as illustrated, fastening the closures and leaving the pull tab outside.11
Follow the manual’s water-testing procedure in calm, protected water with supervision and help available. For oral testing, remove the cylinder; on MD4032, also remove the cap and bobbin. Never activate a device already filled with air. After CO₂ inflation, you may need to blow in extra air by mouth. Mustang calls for two rearming kits: one for initial testing and one spare aboard.11
Cleaning an inflatable
For these models, hand-wash or sponge with warm, soapy water while keeping water away from the inflator. Rinse and hang on a plastic hanger. Store fully dry in a warm, dry, ventilated place outside direct sunlight. Avoid dry-cleaning, chlorine bleach and direct heat. Do not alter it, tie or sew anything around it, or use it as a fender or kneeling pad.11
Where next
Use choosing a life jacket, sizing and fit, types and levels and inflatables for paddlers for selection. Continue with paddle care or the accessories guide.
Footnotes
-
https://uscgboating.org/recreational-boaters/life-jacket-wear-wearing-your-life-jacket.php ↩ ↩2 ↩3 ↩4 ↩5 ↩6 ↩7 ↩8
-
https://explore.astraldesigns.com/FAQs/ ↩ ↩2 ↩3 ↩4 ↩5 ↩6 ↩7 ↩8 ↩9 ↩10 ↩11
-
https://www.nrs.com/assets/downloads/nrs/pfd-notification.pdf ↩ ↩2 ↩3 ↩4 ↩5 ↩6 ↩7 ↩8 ↩9 ↩10 ↩11
-
https://mustangsurvival.com/support/articles/4402064415255-Warranty-Repair-Policy ↩ ↩2 ↩3 ↩4 ↩5
-
Wayback Machine copy captured August 19, 2026 of https://www.dco.uscg.mil/CG-ENG-4/PFDSel/ ↩
-
https://www.ecfr.gov/current/title-33/section-175.23 ↩ ↩2 ↩3
-
https://safeboatingcampaign.com/news/new-life-jacket-labels/ ↩
-
https://files.dnr.state.mn.us/education_safety/safety/boatwater/h2otoons.pdf ↩
-
https://www.ecfr.gov/current/title-33/chapter-I/subchapter-S/part-175/subpart-B ↩
-
https://public-inspection.federalregister.gov/2024-28264.pdf ↩
-
https://cdn.shopify.com/s/files/1/0253/5273/2717/files/h5m37lwzi6ufviibyzts.pdf?v=1781560044 ↩ ↩2 ↩3 ↩4 ↩5 ↩6 ↩7 ↩8 ↩9 ↩10 ↩11 ↩12 ↩13 ↩14 ↩15 ↩16 ↩17 ↩18 ↩19
-
Wayback Machine copy captured November 23, 2025 of https://marinesafety.sa.gov.au/your-safety-and-operations/looking_after_your_lifejacket ↩
-
Wayback Machine copy captured October 16, 2025 of https://paddleuk.org.uk/multiple-buoyancy-aid-and-life-jacket-recalls-8/ ↩
-
Wayback Machine copy captured October 16, 2025 of https://paddleuk.org.uk/multiple-buoyancy-aid-and-life-jacket-recalls-3/ ↩
-
https://www.paddleni.org.uk/multiple%20buoyancy%20aid%20and%20life%20jacket%20recalls ↩
-
https://mustangsurvival.com/blogs/resources/pfd-inspection-and-maintenance ↩