Accessories

Canoe Skid Plates: What It Is and How It Works

Use these rules to choose your next step:

  • If the ends are sound and show little wear, leave them as they are for now. Reconsider if you will often paddle in considerable whitewater: for that, the Canoe Care & Maintenance guide recommends installing skid plates now rather than later.1
  • If wear has exposed underlying material, assess protection and repair together. Northwest Canoe identifies exposed fabric on composite canoes and lighter-colored ABS plastic or foam on Royalex canoes as signs that skid plates are due.4 The Canoe Care & Maintenance guide calls for structural repair when damage exposes the innermost foam core.1
  • If you want removable protection over a sound surface, consider adhesive strips. KeelEazy can be removed or reset with low heat.3
  • If you choose felt and resin, match the kit to the hull before buying. The Canoe Care & Maintenance guide warns that a kit designed for Royalex or composite canoes may not work well on polyethylene.1

What a skid plate protects

The hull is the canoe’s outer body; the stems are its front and rear ends. Northwest Canoe describes skid plates as protection for stems worn by scraping over shoals and shallows.4 A felt-and-resin plate becomes a stiff, hard layer that resists abrasion and deflects impact, according to the Canoe Care & Maintenance guide.1

Fit matters as much as material. That guide calls for complete contact between plate and hull and warns that wide felts intended for blunt-ended canoes can blunt the finer ends of composite boats, reducing paddling efficiency.1 Choose coverage for the wear area and hull shape rather than the largest available patch.

Before covering damage, separate surface wear from a repair problem. The Canoe Care & Maintenance guide identifies spiderweb cracks or missing pieces in gelcoat—the outer finish on many composite hulls—as reasons for gelcoat repair.1 It also warns that unusually flexible material around a scratch may indicate structural damage.1

If damage is difficult to judge, arrange an assessment first. Nova Craft offers composite-hull repairs and skid-plate installation, accepts photographs for estimates, and can recommend repair shops outside its area.5

Choose the system and coverage

KeelEazy is PVC with an adhesive backing; its installation method uses surface cleaning, positioning and low heat.2,3 Old Town’s kit uses Kevlar felt saturated with mixed resin and hardener, followed by curing.6 Choose between them after confirming compatibility, coverage and whether you can carry out the required installation.

For an adhesive system, KeelEazy reports that its testing on polyethylene whitewater boats suggests adhesion comparable to fiberglass and ABS.2 For felt kits, Northwest Canoe describes its resin systems as suitable for ABS and composite hulls, while its Tandem/Universal listing also names polyethylene.4 Confirm the exact kit for your canoe’s material and model before ordering.

Northwest Canoe sizes its felts by hull shape and the area needing protection.4

KitMaker’s suggested fitFelt dimensions
Solo/CompositeSleeker tandems and most solo canoes32 × 3 inches (81 × 7.6 centimeters).4
Tandem/UniversalMost other tandems and some wider-nosed Royalex solos38 × 5 inches (97 × 13 centimeters).4
Livery ToughBroad-entry canoes with extensive surface damage44 × 7 inches (112 × 18 centimeters), tapering to 2 inches (5.1 centimeters) near the waterline.4

Compare the proposed outline with your actual wear area before purchasing. KeelEazy allows protection only where needed rather than along the entire keel.2 Its instructions permit shortening the strip with scissors and require rounded corners; kit pieces arrive with the corners already rounded.3

Check package quantity separately from dimensions. Old Town lists two felts, two resin containers, two hardener containers, two sandpaper pieces and two stirring sticks.6 Ask the seller to confirm whether another package covers both ends and includes everything required for its stated coverage.

Gather supplies before starting

For KeelEazy, the maker lists a heat gun or hairdryer, isopropyl alcohol, a leather glove and scissors; a knife or razor blade may be needed for backing separation or cutting around a skeg.3 Its kits include isopropyl alcohol, and a roller or squeegee can help smooth bubbles.3

Old Town’s additional supply list includes safety glasses, disposable gloves, two disposable paintbrushes, masking tape, a plastic drip cover, plastic wrap, measuring tape and a clean, dry cloth.6 Its manual also lists a propane torch for polyethylene canoes.6

Do not substitute another kit’s preparation or timing. Swift’s Kevlar Skid Plate Installation, specifically describing its Royalex canoes, gives about 10 minutes of working time, while Old Town gives 20 minutes at 70°F (21°C).7,6 Swift requires at least 24 hours in a warm, dry area for full curing; Old Town specifies a 24-hour cure.7,6

Choose a workday that accommodates the complete method, including curing.

Install adhesive protection: KeelEazy’s method

KeelEazy specifies application at room temperature, approximately 70°F (21°C).3 The following sequence follows its Installation Instructions.3

  1. Prepare the hull. KeelEazy requires cracks and holes to be repaired first; lightly sand deep gouges smooth and clean the bonding area thoroughly with isopropyl alcohol.3
  2. Shape the strip. Round its corners and ends with scissors unless your kit already has rounded ends.3
  3. Separate the backing. Remove only the blue backing, leaving the adhesive attached to the strip; the maker allows a razor blade if needed to start separation.3
  4. Position the protection. Attach one end firmly, then center the strip over the keel with a slight stretch; shorten it with scissors if necessary.3
  5. Smooth it into place. Work from the middle toward each end and from the keel’s highest point outward to remove wrinkles and bubbles.3 KeelEazy specifies a hairdryer or heat gun on low and warns against overheating.3
  6. Handle sharp corners. Where necessary, notch or scallop the strip at the corner; if this creates overlapping flaps, KeelEazy directs the leading edge to overlap the other flap so it will not catch during movement.3
  7. Reset if needed. Apply low heat and lift the strip to reposition or remove it.3

KeelEazy’s FAQ says the boat is ready to use after installation.2 For surface cleaning, KeelEazy restricts acetone to fiberglass boats, excludes ABS and polyethylene boats, and specifies an isopropyl-alcohol cleaning afterward.2 Use the isopropyl-alcohol preparation in its installation instructions.

Install felt and resin: Old Town’s method

Use this sequence only with the matching Old Town kit and canoe. Old Town’s Kevlar Skid Plate Installation Instructions requires reading the complete instructions, wearing safety glasses when handling tools and equipment, and working in a well-ventilated area outside direct sunlight.6

  1. Position and outline the felt. Turn the canoe upside down; Old Town specifies measuring 14 inches (36 centimeters) from the edge of the back deck toward the bottom to locate the narrow end.6 Hold the felt with two pieces of tape and mask a border ⅛ inch (3 millimeters) around it.6
  2. Prepare the bonding area. Remove the felt, sand inside the outline with the supplied 40-grit paper, resand any shiny missed spots, and wipe away debris with a clean, dry cloth.6
  3. For polyethylene only, apply Old Town’s surface treatment. Remove the tape outline and briefly sweep the tip of the propane flame’s inner blue cone across the sanded area, moving smoothly and quickly.6 Old Town warns against shining, melting or blackening the surface and against touching it afterward; if a spot was missed, it specifies waiting 20 minutes before repeating the treatment.6 Reattach the tape outline.6
  4. Protect the surrounding hull. Tape the drip cover to the outline without overlapping the working area, sealing the outline against resin runs.6
  5. Mix one batch. Wearing gloves as Old Town directs, pour all of one hardener container into one resin container and stir thoroughly, scraping the container’s sides.6 Old Town gives 20 minutes of working time at 70°F (21°C), with substantially less time at higher temperatures.6
  6. Wet the felt completely. Brush resin over the sanded area, place the felt, and pat it into the resin with a gloved hand or brush.6 Add resin until the felt is wet through, working trapped air out with the brush.6
  7. Finish the edges. Brush firmly and evenly, feathering the felt edges level; when the resin has gelled enough not to run, roughly 15 minutes, remove the drip cover and tape.6 Old Town allows smoothing the edges with a gloved finger or wedge and suggests plastic wrap over the plate for a smoother finish.6
  8. Cure and repeat. Old Town specifies a 24-hour cure and permits light sanding afterward.6 It explicitly prohibits using leftover mixed resin for the second plate; repeat the installation at the other end with the remaining felt and unopened resin components.6

If the flame-treatment step is beyond your skills, arrange installation with a repair professional.

Problems that should stop the job

Pause before covering an unresolved crack or hole: KeelEazy requires those repairs first.3 Likewise, the Canoe Care & Maintenance guide calls for structural repair where damage reaches the innermost foam core.1

During a Swift Royalex installation, Swift directs you to smooth curling felt edges down with your fingers as they cure so they adhere fully.7 Follow the correction instructions for your own kit rather than borrowing a different maker’s timing.

If compatibility, resin mixing or surface treatment remains uncertain, contact the maker before starting. Swift’s manual explicitly asks owners with questions to call the factory before beginning work.7 KeelEazy also states that it does not warranty installation or guarantee successful installation by the user.2

Before returning to the water

Keep the final inspection separate from the modification. The American Canoe Association advises inspecting equipment before every trip, knowing how to right and reenter your craft after a capsize, and avoiding conditions beyond your skills.8

The U.S. Coast Guard recommends wearing an approved life jacket while underway and specifies that it must suit the wearer and activity and remain serviceable.9 Washington State Parks advises checking your vessel’s usability and matching both boat and skill level to the conditions.10 The National Weather Service advises checking the forecast before departure and carrying essential safety equipment and communications tools.11

Choose protection after identifying your hull material and wear area, resolve repair questions first, and reserve enough time for the selected maker’s complete installation. If you cannot meet its preparation or curing requirements, arrange installation before scheduling the canoe’s return to use.

Footnotes

  1. https://media.pelicaninternational.com/m/13d1c49cb161e14d/original/Canoe-Care-Maintainence-Guidelines.pdf ↩ ↩2 ↩3 ↩4 ↩5 ↩6 ↩7 ↩8 ↩9

  2. https://www.keeleazy.com/pages/faqs ↩ ↩2 ↩3 ↩4 ↩5 ↩6 ↩7

  3. https://www.keeleazy.com/pages/installing-keeleazy ↩ ↩2 ↩3 ↩4 ↩5 ↩6 ↩7 ↩8 ↩9 ↩10 ↩11 ↩12 ↩13 ↩14 ↩15 ↩16 ↩17

  4. https://northwestcanoe.com/canoe-skid-plates ↩ ↩2 ↩3 ↩4 ↩5 ↩6 ↩7

  5. https://www.novacraft.com/repairs-maintenance/ ↩

  6. https://johnsonoutdoors.widen.net/content/5k29u7uv36/pdf/CAR_productmanual_Skid_Plate_Kit.pdf ↩ ↩2 ↩3 ↩4 ↩5 ↩6 ↩7 ↩8 ↩9 ↩10 ↩11 ↩12 ↩13 ↩14 ↩15 ↩16 ↩17 ↩18 ↩19 ↩20 ↩21 ↩22

  7. https://swiftcanoe.com/wp-content/uploads/2020/09/KevlarSkidPlateInstallation.pdf ↩ ↩2 ↩3 ↩4

  8. https://americancanoe.org/wp-content/uploads/documents/sei-educational_resources/best_practices.pdf ↩

  9. https://www.uscgboating.org/recreational-boaters/life-jacket-wear-wearing-your-life-jacket.php ↩

  10. https://parks.wa.gov/find-activity/activity-search/paddlesports ↩

  11. https://www.weather.gov/safety/safeboating-before ↩